Stiff uPVC windows usually get worse so slowly that you barely notice, until one day the handle won’t budge. Most of the time, though, the cause is simple: dirt, dry moving parts or a small misalignment.
A little cleaning and the right lubricant fix plenty of stiff uPVC windows in minutes. This guide shows you how to diagnose the problem, what to lubricate, which products to use and avoid, and when to call a professional.
If your windows are 15 years old or more, as many are, this is a job worth adding to your autumn checklist.
Why uPVC windows get stiff
Stiffness almost always comes from one of a handful of causes:
- Dirt and grit packed into the hinges and tracks.
- Dry or corroded hinge pivots and sliding shoes.
- A dry or worn locking mechanism along the edge of the sash.
- Keeps on the frame that no longer line up with the locking cams.
- Locking cams set too tight, often after a winter adjustment.
- A dropped sash rubbing on the frame.
- Hot weather, because uPVC expands and gaskets can stick.
The first three respond well to cleaning and lubrication. The others need a small adjustment or, occasionally, a repair. So, it pays to work out which one you’ve got before reaching for the oil.
Diagnose it first: where is the stiffness?
Diagnosing stiff uPVC windows starts with the window open. Turn the handle through its full travel, then swing the sash slowly, and finally close and lock it. Notice exactly when it feels stiff.
| Symptom | Likely cause | First step |
|---|---|---|
| Handle stiff even with the window open | Dry or worn gearbox or locking bar | Lubricate the mechanism; replace the gearbox if no better |
| Handle stiff only as it locks | Cams catching the keeps, or tight compression | Lubricate the keeps; ease the cams |
| Sash hard to swing | Dirty or dry friction hinges | Clean and lubricate the hinges |
| Sash rubs or scrapes the frame | Dropped sash or worn hinges | Hinge adjustment or replacement |
| Window sticks shut on hot days | uPVC expansion or sticky gaskets | Treat gaskets; check alignment |
| Sash won’t stay where you leave it | Hinge friction too loose | Tighten the friction screw, if fitted |
A handle that’s smooth with the window open but stiff when closed points to alignment rather than wear. By contrast, a handle that crunches with the window open usually means the gearbox is failing.
If lubrication does not help and the handle turns without locking, the gearbox may be worn. Our Reading team explains what to do when a uPVC window will not lock or the handle spins.
What to lubricate on stiff uPVC windows
There are four areas to treat. Each one needs a slightly different approach.
Friction hinges
These are the metal arms at the top and bottom of a side-hung sash. First, brush or vacuum out the track. Then apply a little light machine oil or silicone spray to the pivots and the sliding shoe.
Work the window open and shut a few times, then wipe off any excess. However, go easy, because some hinges rely on friction to hold the sash open. If it now drifts in a breeze, tighten the friction adjustment screw where one is fitted.
The locking mechanism
Along the opening edge of the sash is a metal bar with small locking cams, either rollers or mushroom-shaped heads. They engage keeps fixed to the frame.
Put a drop of oil on each cam and along the moving bar. Next, add a light smear of grease or petroleum jelly to the keeps. Finally, work the handle several times so it spreads.
The gearbox
The gearbox sits behind the handle and turns its movement into the sliding action of the bar. A drop of light oil where the bar meets the gearbox can help. That said, a gearbox that crunches or binds usually needs replacing, not oiling.
Gaskets
Rubber gaskets don’t need oil, and some oils can make rubber swell or turn tacky. If gaskets stick, wipe them clean and treat them with a silicone spray or a gasket conditioner instead.
Lubricants to use, and ones to avoid
The right product makes a big difference. Here’s a quick guide.
| Product | Use it on | Avoid using it on |
|---|---|---|
| Light machine oil | Hinge pivots, cams, locking bar | Gaskets and frame faces |
| Silicone spray | Gaskets, tracks, sliding shoes | Surfaces you’ll paint or seal later |
| Dry PTFE spray | Tracks in dusty or sandy spots | Nothing specific, but wipe off overspray |
| Petroleum jelly or light grease | Keeps and strikers | Hinge tracks, where it traps grit |
Some products cause more trouble than they solve. For example, cooking oil turns sticky, heavy grease attracts dirt, and multi-purpose water-displacing sprays clean well but don’t last long as a lubricant.
Also, keep harsh cleaners off the frames. Bleach, solvents, cream cleaners and abrasive pads can dull or scratch uPVC. Warm water with a little washing-up liquid is all most frames need.
Windows still stiff after a clean and oil?
We repair hinges, gearboxes and locking mechanisms across Farnborough. There’s no call-out fee, quotes are free and our repairs come with a 12-month guarantee. Call us or send a short video on WhatsApp.
A simple twice-yearly maintenance routine
Spring and autumn suit most homes. It takes about ten minutes per window, and it’s the best way to prevent stiff uPVC windows in the first place.
- Open the window fully and vacuum the hinges, tracks and frame channel.
- Clear the drainage slots along the bottom of the frame with a soft brush.
- Wash the frame and sash with warm, soapy water, then dry them.
- Oil the hinge pivots and sliding shoes lightly.
- Oil the locking cams and bar, and grease the keeps.
- Treat the gaskets with silicone spray if they look dry or stick.
- Open, close and lock the window several times.
- Wipe away any excess so grit can’t build up.
While you work, check for loose screws in the hinges, keeps and handle. A loose hinge screw is easy to tighten now, but it can strip the frame if ignored.
It’s also a good moment to look at the glass. Misting between the panes is a separate fault, caused by a failed seal, and our misted double glazing repairs page explains the fix. If you’re in Farnborough, we can deal with both at the same visit.
The Glass and Glazing Federation, the industry’s trade body, also publishes consumer guidance on caring for windows and doors.

Stiff uPVC windows through the seasons
Windows behave differently as the weather changes. Knowing why helps you treat the cause rather than the symptom.
Summer
uPVC expands noticeably in heat, especially on dark-coloured frames and south-facing walls. As a result, stiff uPVC windows are often at their worst on a hot afternoon. Gaskets can also soften and grip the frame.
So, if a window only sticks on warm days, treat the gaskets with silicone spray and check the cams aren’t set too tight. Don’t force it open in the heat of the day if it eases by evening.
Winter
In cold weather, the opposite happens. Frames contract, and many people tighten the cams to stop draughts. That’s fine, but a very tight setting makes the handle hard work.
Also, damp autumn weather is when dry hinges start to corrode. That’s why an autumn clean and lubricate pays off before the first frosts.
Simple adjustments for stiff uPVC windows
If cleaning and lubrication don’t help, the next step is often a small adjustment.
Easing the locking cams
Many uPVC windows have adjustable cams. These are small round or oval heads on the locking bar, often with an Allen key slot or a flat for pliers. Turning them changes how tightly the sash presses against the seals.
A tighter setting seals better but feels stiffer. So, if a window became hard to lock after someone adjusted it for winter, ease each cam back a notch.
Adjust every cam on the sash by the same amount. Also, photograph each one before you touch it, so you can return it to where it was.
Hinge and keep alignment
On some systems, keeps can be shifted slightly to meet the cams. However, misaligned keeps usually signal a sash that has dropped. In that case, the fix is at the hinges, not the keeps.
When stiff uPVC windows need a repair
Lubrication fixes dry parts, but it can’t fix broken ones. Call a professional if you notice any of these:
- Cracked, bent or rusted friction hinges.
- Sash dropped and scraping the frame.
- Handle crunching or binding with the window open.
- Window that won’t lock, or only locks with force.
- Hinge screws pulling out of the frame.
- Heavy sash sagging when it’s open.
Never force a stiff window, especially upstairs. If a hinge breaks while the sash is open, it can drop or swing out unexpectedly.
Typical repair costs
- Cam or keep adjustment: often a few minutes during any visit.
- Pair of friction hinges, supplied and fitted: typically £70–£150.
- Gearbox replacement: typically £80–£160.
- Full locking mechanism: typically £100–£200, depending on size.
These are typical UK ranges. Our window repair cost guide covers more jobs, and our services page lists everything we repair.
Quick answers
What’s the best lubricant for uPVC windows?
Light machine oil works well on hinges, cams and the locking bar. Use silicone spray on gaskets and tracks instead of oil.
How often should I lubricate uPVC windows?
Twice a year suits most homes. Windows on exposed or dusty sides of the house may need it more often.
Why are my windows hard to close in summer?
uPVC expands in heat, and gaskets can stick. As a result, a window that’s slightly tight in winter can bind on a hot day.
Can I adjust my window myself?
Easing locking cams is a reasonable DIY job with care. However, hinge replacement and dropped sashes are best left to a professional.
Why is my handle still stiff after lubricating?
The gearbox may be worn, or the sash may be out of alignment. Either way, it’s worth getting it checked before something snaps.
Keep them moving
Most stiff uPVC windows need nothing more than a clean, the right lubricant and a few minutes of attention. Do it twice a year, and your hinges and locks will last far longer.
If a window still fights you, get it looked at before a part breaks. We cover the whole area, including window repairs in Mytchett and Frimley Green. See our areas we cover page for the rest.
Stiff or sticking windows in Farnborough?
Call us or send a quick video on WhatsApp, and we’ll tell you what’s wrong. No call-out fee, free quotes, 12-month guarantees and a 24/7 emergency service for windows that won’t lock.



